38 results
Filters
Settings
Now showing1 - 10 of 38
- Some of the metrics are blocked by yourconsent settings
Item type:Project, Access status: without files , 21 - Some of the metrics are blocked by yourconsent settings
Item type:Project, Access status: without files , 22 - Some of the metrics are blocked by yourconsent settings
Item type:Project, Access status: without files , Investigation of Seabed-Anchor Interaction of Floating Offshore Wind TurbinesIn the future, floating offshore wind turbines (FOWTs) will increasingly offer the possibility of generating renewable energy even at locations with great ocean depths. An essential element is the safe and reliable anchoring of these platforms at the sea bed. In practice, a fixed bearing has been assumed up to now. It is well known that this assumption is not conservative. The underlying physical principles of the seabed-anchor interaction have yet not been completely understood. This interaction depends on the anchor type, its installation process, and the drainage conditions of the seabed. Other influences result from load direction and velocity. Yielding and failure results from the complex combinations of wave, current, wind, and operational loads, which pose a challenge to the safe and reliable operation of FOWTs. The deployment of FOWTs is still in its early stages. While there is a transfer of knowledge from the oil and gas industry in certain areas, the aforementioned influences on sedbed-anchor interaction and the interaction itself are largely unexplored. The research project is intended to contribute to a fundamental mechanical understanding of the soil-anchor interaction so that it can be modelled as a component of the design of anchored FOWT. Based on the fundamental research, a simplified drag embedment anchor model (anchor force as a function of anchor chain motion) will be developed to describe the soil-anchor interaction, taking into account anchor geometry, seabed, and load history. The anchor model describes the reaction force of the anchor for a given velocity and direction of the anchor load. To achieve the defined objectives, anchor models will be developed based on the following steps. In the beginning, the movement of the floating offshore platform of a reference installation and the resulting force at the anchor point due to wind, waves and currents will be calculated for different load scenarios. Preliminary numerical investigations follow this to calculate the anchor resistance and displacement considering the seabed-anchor interaction based on a continuum model for the saturated seabed, a rigid body motion for the anchor and possibly the part of the anchor chain on the seabed, and a contact model for the anchor/seabed and chain/seabed interface. Model tests in the centrifuge will validate the numerical model at prototype scale. In addition, the tests will serve to determine the anchor pull-out resistance. A parameter study will be used to investigate the soil-anchor interaction for the reference plant based on the validated FE model. In the final phase of the research project, an anchor model will be developed as a component of future mooring analyses.28 - Some of the metrics are blocked by yourconsent settings
Item type:Project, Access status: without files , Experimental investigation of capillary collapse of partially saturated granular soils during saturationThe capillary collapse is an irreversible volume reduction of partially saturated soils caused by provision of water at essentially unchanging total vertical stress. The cause of this phenomenon is probably, among other factors, the increasing dissolution of the capillary bridges, which is accompanied by a reduction in the stabilizing capillary cohesion and ultimately leads to rearrangements of the grain structure. Loosely bedded, fine-grained soils with a metastable microstructure are particularly at risk in this context. So far, existing studies on capillary collapse focus mainly on the macroscopic investigation, which is why the processes occurring on the micro-scale are still poorly understood. Within the framework of this research project, a better understanding of the physical processes occurring in granular media during capillary collapse on the particle scale is therefore to be gained. For this purpose, three different model soils, which show an increasing degree of complexity due to deviations from the simplest, idealized particle mixture (spherical particles with homogeneous density and uniform size), will be investigated. The starting point of the investigations is a poly disperse packing of industrially manufactured glass beads. In the next step, a model soil of natural, randomly shaped sand particles is investigated. The starting point of the investigations is a poly disperse packing of industrially manufactured glass beads. In the next step, a model soil of natural, randomly shaped sand particles is investigated. Since dump soils from opencast lignite mining are among the most endangered soils in Germany, another model soil will be investigated that contains lignite particles naturally occurring in opencast mine dump soils in addition to the sand grains as an example of a special particle structure (micro-porosity). In situ CT experiments with the help of the three-dimensional image data recorded over time allow insights into the processes taking place at the micro level as well as an analysis of the particle movements, whereby the knowledge gained can contribute significantly to the development of a deeper understanding of the collapse processes during saturation. Microscopic changes, e.g. in the phase distribution and capillary menisci, can be recorded and the relation to the occurring macroscopic collapse deformations can be analyzed. In the planned macroscopic and microscopic experiments, the influence of various boundary conditions such as the applied vertical stress, the lignite content, the irrigation rate and irrigation direction or the matric suction present in the soil will be quantitatively investigated.12 - Some of the metrics are blocked by yourconsent settings
Item type:Project, Access status: without files , Adhäsion zwischen ebenen Stahloberflächen und kohäsiven BödenA deeper understanding of the contact surface between a structure or tool and the surrounding soil is fundamental for many geotechnical applications. Applications range from pile structures, which mobilise their load-bearing capacity via their shaft, to cutter heads of tunnel boring machines, whose advance rate is significantly characterised by the conditions in the interface with the ground. In most geotechnical applications, the Mohr-Coulomb friction law is used to describe the interaction between soil and structural surface. For coarse-grained soils this approach is applicable, but for fine-grained soils the behaviour in the interface is much more complex. Adhesion and stickiness of the material occur and there seem to be forces in the interface that are not only related to friction. To date, there is no satisfactory model that can fully represent the behaviour between a steel surface and a fine-grained soil. One of the aims of the present research project is to create an experimental database that allows models of the interfacial behaviour between fine-grained soils and steel to be derived. This is based on an extensive experimental programme with specialised experimental techniques and controlled sample preparation. Based on the findings, numerical modelling approaches for the interface will be developed. The developed models can be applied in many geotechnical problems, such as tensile piles in fine-grained soils as well as adhesion phenomena occurring in mechanised tunnelling. The consideration of adhesion can lead to a more economical design and the possibility to simulate adhesion could enable a better prediction of tool clogging as a function of soil properties.8 - Some of the metrics are blocked by yourconsent settings
Item type:Project, Access status: without files , Holistic approach for the design of single piles and pile groups under cyclic loadingLong term load-displacement behaviour of piles under cyclic axial and lateral loading is essential for the design of pile foundations. The prediction of this behavior is linked to large uncertainties due to the distinct type of cyclic loading as well as the extremely high numbers of load cycles compared to conventional engineering structures. There is a need of a design approach being able to cover the soil behavior under cyclic and high-cyclic loading and the specific behavior of pile constructions. Existing design approaches show significant uncertainties already for monotonic loading. The major objective of the research project is the further development of a design approach based on an existing subgrade reaction method called SRMHYP, that is currently designed for lateral cyclic loaded single piles in sand. This model is planned to cover the following cases at the end of the project: single piles and pile groups, sand and clay, cyclic and high-cyclic axial and lateral lading, soil stiffness for small and large deformation, rate-independent behavior of sand and rate-dependent behavior of clay, effects due to pile installation and set-up. This extended model will be validated by means of centrifuge tests, numerical simulations, and existing results of field tests. All planned experiments, models and numerical simulations are designed for two different model soils, namely a fine uniform silica sand and a kaolin clay representing non-cohesive and cohesive soils. The results of the laboratory tests on sand and kaolin with cyclic loading are used as input parameters for the SRMHYP model, for further development of a stress-strain model for kaolin, for further development of high-cycle accumulation models for sand and clay, and for calibration of hypoplastic and visco-hypoplastic models for sand and clay. The results of the centrifuge tests on cyclic loaded piles in sand and clay under defined conditions are used to validate the SRMHYP model, and additionally the numerical simulations, because the tests are carried out under a realistic stress level. The numerical simulations of piles under cyclic and high-cyclic loading are based on the continuum approach and the FEM. Therefore, the further developed of the stress-strain model for clay and the accumulation models for sand/clay mentioned above are applied. Additional work on the contact model for the contact surface pile/soil as well as work on the user subroutines for the FE-program are necessary. The results of the numerical simulations serve as a basis for the abstraction of the simpler and less computer consuming SRMHYP model. The simulation models are validated by means of results of centrifuge tests and results from field tests.29 - Some of the metrics are blocked by yourconsent settings
Item type:Project, Access status: without files , Micro-mechanical modelling of unsaturated packings using CFD-DEM and computed tomography (MIME-UP)The main objective of the proposed project is to investigate the influence of capillary effects in partially saturated sands on their mechanical and hydraulic behaviour. Therefore, numerical simulations as well as micro-scale experiments in an x-ray tomograph are planned. For the numerical simulation of partially saturated sands, the resolved CFD-DEM will be used. The existing method will be supplemented by a two-phase flow formulation to consider the influence of pore water and pore air. The micro-scale experiments performed in the x-ray tomograph will be used to validate the newly developed models. Special attention is thereby paid to the formation of capillary bridges during desaturation of a sand column as well as the deformation behaviour and load-response in a triaxial test. For this purpose, the computation of the interaction between particles, fluid and a deforming, load-responsive membrane will be developed in the framework of resolved CFD-DEM. In a possible extension of two years, unsaturated triaxial tests will be conducted in the CT-tomograph to understand the hydro-mechanical behaviour of sand. The developed tools of the first funding period will be combined and extended to model unsaturated triaxial tests.To reach the defined objectives a co-operation between Hamburg University of Technology/Germany and DCS Computing Linz/Austria is planned. DCS is developing the code CFDEMÒcoupling, which is used in the research project. This cooperation is covered by the D-A-CH agreement (DFG in Germany and FWF in Austria).44 - Some of the metrics are blocked by yourconsent settings
Item type:Project, Access status: without files , 24 - Some of the metrics are blocked by yourconsent settings
Item type:Project, Access status: without files , 104 - Some of the metrics are blocked by yourconsent settings
Item type:Project, Access status: without files , On the loss of contact between driving element and soil during vibratory driving into saturated soilThe vibration driving of piles is a tried and tested method of driving the pile into the ground quickly and economically. Compared to other methods, vibration pile driving represents a relatively low-vibration and low-noise introduction of the pile. Current studies show insufficient agreement with the observations and interpretations of corresponding experiments. When moving upwards, a cavity can form under the pile base. The nature of this presumed void is not fully understood. In addition, the separation between pore water and soil particles and a possible phase transition of the pore water to water vapor (cavitation) due to the negative pressure have not been adequately researched. The cavitation pressure required for this is achieved when the pore water cannot flow into the cavity with sufficient speed due to the permeability of the soil. The main aim of the research project is therefore to clarify the processes at the pile base during the upward movement during vibration driving and the influence of the subsequent static load-bearing behavior through the installation process. Another aim is to investigate the influence of physical cavitation and the suspected cavity under the pile base during vibration driving. For this purpose, computer simulations are carried out, which are validated with the help of model tests.71