19 results
Now showing1 - 10 of 19
- Some of the metrics are blocked by yourconsent settings
Item type:Publication, Access status: with files , Experimental and numerical investigation of brittle ice crushing loads(2023); Ice loads pose a significant risk for ship operation in ice covered waters. At low strain rates, the ice behaves ductile, whereas at high strain rates it reacts in brittle manner. This thesis focuses on the brittle mode, which is the dominating mode for ship-ice interactions. A multitude of experimental data and numerical approaches for the simulation of ice can be found in the literature. Nevertheless, versatile and profound validated simulation techniques are currently missing to access the consequences of an iceberg collision or ice floe impact. Hence, in this thesis the new experimental set-up of the ice extrusion tests for the investigation of ice crushing loads is presented and a finite element model for the simulation of brittle ice-structure interaction problems is developed. During the comprehensive ice extrusion test campaign confined ice specimens were pushed against quasi rigid or full-scale ship structures. The obtained results reveal that the failure mode depends mainly on the test speed, while the confinement of ice mainly determines the load level. The core objective of the developed Mohr-Coulomb Nodal Split (MCNS) ice material model is to enable efficient physical based ice-structure interaction simulations. Unlike previously existing ice models, the MCNS model takes spalling and crushing into account, which significantly increases the versatility and reliability of the approach. The confinement effect on the crushing strength and the anisotropic failure behaviour of the ice is modelled by the Mohr-Coulomb material model. To preserve mass and energy as much as possible, the node splitting technique is applied in addition to the element erosion technique. To validate the findings of the model, the simulated maximum ice forces and contact pressures are compared with small- and large-scale ice extrusion experiments and double pendulum tests. During validation, the MCNS model shows a very good agreement with these experimental results. Finally, a procedure is proposed to simulate full-scale ship-ice collisions on basis of the given methodologies and experimental results.Publicationtype: Doctoral Thesis272 2834 - Some of the metrics are blocked by yourconsent settings
Item type:Publication, Access status: with files , A time domain boundary element method for fluid-structure interaction analysis on a discontinuous surfaceIn this thesis, the development of the two-dimensional time domain solver cBEM for modeling linear hydrodynamic problems is described. The approach was based on Potential Flow Theory and applied Boundary Integral Equations with that the governing Boundary Value Problem was solved and the interactions of body and surface gravity waves were modeled. The embedding of the High-Order Spectral procedure into the Boundary Element Method in the symmetric Galerkin formulation represents an innovative coupling method for the treatment of hydrodynamic problems. The explicit account of a surface discontinuity represented by the body in the free surface boundary domain, the strategy of incorporating the High-Order Spectral approach in the Boundary Element Method, and the development of suited desingularization techniques for kernel functions up to hypersingular order had been considered within this thesis. As higher-order basis functions had been used for the approximation of solution function space and geometry, the results of cBEM in terms of the boundary quantities, the potential and its normal derivative, were of good accuracy. cBEM can be accounted as the foundation of a highly efficient three-dimensional nonlinear Boundary Element Method solver with possible future application e.g. in the research fields of analyzing nonlinear body motion due to nonlinear wave excitation in numerical wave tanks and for the optimization of ship hull geometries in the early design phase. For offshore operations, the deterministic wave and motion prediction would help to increase safety and cBEM was designed to fit into a holistic approach containing wave inversion, nonlinear wave propagation, and motion prediction. The efficient evaluation of the mixed Boundary Value Problem with highly efficient methods would allow predictions over a period of time that meets industry expectations. The work is structured as follows. In the introduction, the scope of the work is highlighted and limitations and innovations are outlined. In the literature review presented thereafter, the Boundary Element Methods used in Marine Hydrodynamics are categorized into three main streams, and related research contributions are summarized. Based on this, the research gap is outlined and a global hypothesis defined. The research hypotheses structure and summarize the main concerns according to the global hypothesis and give the frame for the development of cBEM. In chapter two, the theory of Boundary Integral Equations and numerical tools accounted for in the Boundary Element Method approach are summarized. Furthermore, the Linear Wave Theory and the High-Order Spectral method as well as the basic problems of wave-body interaction are described. On the mathematical foundation and the introduction of the computational methods represented here, the steps for the development of the cBEM solver are presented in chapter three. After an overview of the steps, the Boundary Integral Equations for the different solvers are described. The direct formulation of cBEM is given and the methods accounted for in pre-, post-, and processing are introduced. It follows the verification of the approaches including the free surface solver fsBEM, the coupled solver cBEM, and the transient cBEM solver for the continuous and discontinuous surfaces. The validation section, chapter four, shows the application of cBEM for hydrodynamic problems. The submerged and free surface piercing geometries were considered and linear problems with a forced oscillating body, the free surface elevation over a submerged cylinder, and the diffraction of waves due to a body below were compared with literature references. The final discussion in the review of the research hypotheses follows and the conclusions are drawn. By identifying the status of the work described herein, future steps are pointed out. The extension of cBEM to a three-dimensional solver, equipped with efficient solving strategies and nonlinear extensions is outlined and future applications are given. Their potential is highlighted and the required developments are depicted.Publicationtype: Doctoral Thesis81 124 - Some of the metrics are blocked by yourconsent settings
Item type:Publication, Access status: without files , Effects of corrosion on the local behavior of steel structures under tensile loadingPublicationtype: Doctoral Thesis166 - Some of the metrics are blocked by yourconsent settings
Item type:Publication, Access status: with files , Analyzing the complexity of ice with explainable machine learning for the development of an ice material model(2022-01); Seasonally or partially ice-covered sea areas are attractive to many stakeholders. Ships and structures operating in these areas must be designed to withstand ice-induced loads. This is done with empirical methods and model-scale ice tests, but these have various drawbacks. Numerical simulations are a desirable remedy, but their accuracy is limited because current ice material models only partially capture ice behavior. Improving ice material models is difficult due to gaps in ice mechanics theory and full-scale measurements. Small-scale experimental data is analyzed with explainable machine learning for an improved understanding of ice. An elastic-brittle material model is developed and applied in several studies.Publicationtype: Doctoral Thesis518 2728 - Some of the metrics are blocked by yourconsent settings
Item type:Publication, Access status: with files , Einfluss der lokalen Schweißnahtgeometrie auf die Rissinitiierung an Stumpfstößen(2021-04-05); Publicationtype: Bachelor Thesis94 214 - Some of the metrics are blocked by yourconsent settings
Item type:Publication, Access status: with files , Application of the Strain Energy Density method to butt-welded joints(2021-02); Publicationtype: Bachelor Thesis172 533 - Some of the metrics are blocked by yourconsent settings
Item type:Publication, Access status: with files , Stealth-Technik für Unterwasserfahrzeuge(2021); In this work, the hydroacoustic principals of a stealth outer-hull shape for sonar use are examined for the first time in the open literature. From these principals, the requirements for such a sonar stealth shape are derived. Taking these requirements into account, a sonar stealth shape is designed starting from a generic, classical outer-hull shape of a generic underwater vehicle. The thus obtained sonar stealth shape has significant advantages over a classical outer-hull shape in terms of acoustic scattering, as proven through numerous calculation examples.Publicationtype: Doctoral Thesis339 1445 - Some of the metrics are blocked by yourconsent settings
Item type:Publication, Access status: with files , Assessment of fatigue strength of welded steel joints at sub-zero temperatures based on the micro-structural support effect hypothesis(2021); Although it is known that the material properties of steel and its welded joints change with decreasing temperatures, little research has been done on fatigue strength at sub-zero temperatures and design curves and methods for room temperature are also applied to sub-zero temperatures. By means of stress-life (S-N) tests, the fatigue strength of welded structural steels at temperatures down to -50 °C was investigated. In addition, fatigue design concepts for welded joints - based on the micro-structural support effect hypothesis - are extended to sub-zero temperatures.Publicationtype: Doctoral Thesis734 1591 - Some of the metrics are blocked by yourconsent settings
Item type:Publication, Access status: with files , Untersuchung eines LNG-Kompensators im kryogenen Bereich(2020-08); In shipping, engines powered by heavy fuel cause high level of climate effecting emmissions. LNG is therefore considered as an alternative to heavy fuel, as combustion of LNG will result in a significant reduction in emissions. This thesis examines the potential use and its feasibility for use of a LNG expansion joint in ships. For this purpose, an expansion joint is tested in a climate chamber to determine its behaviour. In this experiment, the expansion joint is cooled down with liquid nitrogen down to -160 °C in order to measure the force and strain on the expansion joint. The experiment is then simulated with a FE-analysis, whereby a stress analysis is also carried out using FEM. The last step of the verification of the usability of expansion joints in the LNG sector is the calculation of the fatigue life. For this step the maximum stress at the nodes is extracted from the simulation. With this information, using the fatigue class FAT 225, the operational strength is determined in the form of a maximum number of life cycles that an expansion joint can sustain in operation before failure occurs. Based on the knowledge gained from the experiment and simulation, a number of 2220 life cycles can be determined. This corresponds, for a refuelling interval of 14 days, a life expectancy of about 85 years and thus significantly exceeds the average operating time of ships, both in tourism and in freight transport. The results of this thesis provide a basis for research in this field. In the future it is considered useful to conduct further experiments for validation. In addition, further experiments may consider a separation of bellows and pipe of the expansion joint. This could ensure a more reliable evaluation of the material behaviour in the bellows and pipe.Publicationtype: Master Thesis182 1461 - Some of the metrics are blocked by yourconsent settings
Item type:Publication, Access status: with files , Statistical assessment of post-weld treated welded joints by burr grinding(2020-05); Burr grinding is one of the post-weld improvement methods that are widely used in various industries to improve the fatigue strength of welds: bridges, offshore structures, ships and land-based structures. In this paper, main influencing parameters and effect of burr grinding technique on the fatigue strength for butt-welded, longitudinal welded, doubling plates, load-carrying transverse, non-load carrying transverse welded and T-joints as well as I-section with cope hole and out-of-plane longitudinal welds has been evaluated, based on the extracted 395 fatigue data points from 34 existing publications. The specimens used in these studies with yield strength 175 MPa < σYS <1100 MPa, which were tested with stress ratio -1 < R < 0.5, are analyzed and assessed with statistical methods. The assumed value of S-N slope m = 4 and proposed FAT classes seem to be applicable for the extracted data. More experimental testing is needed to draw the conclusion more exactly.Publicationtype: Bachelor Thesis165 464