8 results
Filters
Settings
Now showing1 - 8 of 8
- Some of the metrics are blocked by yourconsent settings
Item type:Publication, Access status: without files , Influence of carbon nanoparticle geometry in epoxy matrix on mechanical properties and failure initiation regarding the size effect(Curran Associates, Inc., 2018-06); ; ; ; The influence of a carbon nanoparticle modification on the damage behaviour and resulting mechanical properties of an epoxy matrix is experimentally investigated. A comparison of different nanoparticle morphologies with regard to their potential use in FRP is carried out. Since the volumes between the fibres in FRP are very small, the focus is set on the investigation of size effects of polymer nanocomposites. The influence of local microdamage at the particles on the mechanical properties in a small volume is discussed by comparing the different energy dissipating damage mechanisms in dependence of the nanoparticle morphology. Crack initiation and damage mechanisms at the different nanoparticles can be clearly identified. For layered particles such as few layer graphene, it is found that the orientation of the graphene layers with regard to loading direction is critical for local damage mechanisms and hence mechanical properties.Publicationtype: Conference Paper49 - Some of the metrics are blocked by yourconsent settings
Item type:Publication, Access status: without files , Combined experimental-numerical approach for the 3D vibration analysis of rotating composite compressor blades: An introduction(Curran Associates, Inc., 2018-06); ; ; ; As compressor blades are subjected to highly dynamic loads, there is a particular interest in determining their modal properties under operating condition. Furthermore, intensive research is conducted for the development of fibre-reinforced epoxy blades due to the high specific stiffness and strength as well as the high damping of composite materials. Traditional modal analysis techniques are state of the art to determine the vibration behaviour of non-rotating/stationary blades, where some new approaches show the vibration analysis of rotating blades. These approaches for rotating structures have the disadvantage, that either the excitation or the measurement method are influencing the dynamic behaviour of the investigated structure or the method itself cannot be applied for composite materials. Other techniques do not allow a continuous or full-field measurement of the rotating structure. To determine the vibration behaviour of rotating composite compressor blades, a combined experimental-numerical approach is introduced. Therefore, an experimental system for the vibration excitation and a 3-dimensional determination of the vibration behaviour of rotating components are presented. An overview of the main addressed research topics is given.Publicationtype: Conference Paper52 - Some of the metrics are blocked by yourconsent settings
Item type:Publication, Access status: without files , Effect of laser surface treatment on the adhesive properties of bonded CFRP joints(Curran Associates, Inc., 2018-06); ; ; ; In this work, the effect of an Ytterbium fibre laser treatment on the adhesive properties of scarf bonded carbon fibre reinforced plastics (CFRP) joints has been investigated. The surfaces were scarfed and afterwards laser treated. The effect of laser treatment on the surface morphology was investigated with scanning electron microscopy (SEM) and X-ray photoelectron spectroscopy (XPS). The laser treatment resulted in a morphological and chemical change on the CFRP surface. The introduced thermal energy was able to partly strip and roughen up the carbon fibres. The laser treatment increased the carbon and decreased the oxygen, nitrogen and sulphur content on the surface. With the laser treatment the static and fatigue strength of the scarf bonded joints could be improved.Publicationtype: Conference Paper98 - Some of the metrics are blocked by yourconsent settings
Item type:Publication, Access status: without files , (Ultra-)low grammage bacterial cellulose nanopaper-reinforced polylactide composite laminates(2018-06); ; One of the rate-limiting steps in the large-scale production of cellulose nanopaper-reinforced polymer composites is the time consuming dewatering step to produce the reinforcing cellulose nanopapers. In this work, we present a method to reduce the dewatering time of bacterial cellulose (BC)-in-water suspension by reducing the grammage of BC nanopaper to be produced. The influence of BC nanopaper grammage on the tensile properties of BC nanopaper-reinforced polylactide (PLLA) composites is also investigated in this work. BC nanopaper with grammages of 5, 10, 25 and 50 g m-2 were produced and it was found that reducing the grammage of BC nanopaper from 50 g m-2 to 5 g m-2 led to a three-fold reduction in the dewatering time of BC-in-water suspension. The porosity of the BC nanopapers, however, increased with decreasing BC nanopaper grammage. While the tensile properties of BC nanopapers were found to decrease with decreasing BC nanopaper grammage, no significant difference in the reinforcing ability of BC nanopaper with different grammages for PLLA was observed. PLLA composite laminates reinforced with BC nanopaper at different grammages possessed a tensile modulus of 10.5-11.8 GPa and tensile strength of 95-111 MPa, respectively, at a = 39-53 vol.-%, independent of the grammage and tensile properties of the reinforcing BC nanopaper(s).Publicationtype: Conference Paper60 - Some of the metrics are blocked by yourconsent settings
Item type:Publication, Access status: without files , Influence of temperature and impact energy on low velocity impact damage severity in CFRPThe present study deals with the effect of temperature and impact energy on the damage in CFRP subjected to low velocity impact. Quasi-isotropic laminates were impacted with energies between 8 and 21 J at temperatures ranging between 20 and 80 ◦C. The resulting damage was assessed using ultrasonic C-scans, radiography and confocal microscopy. The residual strength was evaluated utilizing compressive tests at 20 ◦C. It was found that delamination size is decreasing with increasing temperature. However, severe fibre failure on the impacted side occurs at elevated temperatures. This increases the visual damage detectability on the impacted side drastically while decreasing it on the opposite side. Nevertheless, the residual compressive strength is mainly dependent on the delamination area. As a result, visual damage severity does not correlate with the residual compressive strength. Different impact energies can have the same effect on the residual strength, when impacted at different temperatures.Publicationtype: Conference Paper148 - Some of the metrics are blocked by yourconsent settings
Item type:Publication, Access status: without files , Simulation and optimization of the load introduction geometry of additively manufactured lattice structure specimensAdditively manufactured lattice structures show potential in medical and lightweight applications due to scalability of mechanical properties by the relative density of the cells. This requires characterization of the effective mechanical properties. Often compressive tests are used, however, tensile tests are conducted rarely despite their physical relevance. Current studies show challenges especially in determining reliable values of the effective tensile strength since specimens often fail at the transition from load introduction to lattice structure. The goal of this contribution is to provide guidelines for constructing load introduction geometries leading to failure of the samples within the lattice structure. To optimize the load introduction geometry, nonlinear finite element simulations are performed to identify stress concentrations. Tensile, compressive and single-edge-notch bending experiments of the stereolithography manufactured base material are conducted to calibrate the material model. The simulations show that confined transversal contraction is problematic and that a smooth transition with decreasing relative density of the lattice cells seems promising to determine reliable effective mechanical properties. To validate the simulations, tensile tests of lattice structure specimens with 3D digital image correlation are conducted.Publicationtype: Conference Paper325 - Some of the metrics are blocked by yourconsent settings
Item type:Publication, Access status: without files , Relaxation-driven water diffusion in epoxy resin filled with various carbon nanoparticles(Curran Associates, Inc., 2018); ; ; ; Water sorption-desorption-resorption and swelling were studied for a model epoxy system based on DGEBA resin and triamine curing agent. Four types of carbon nanofillers were incorporated into the epoxy matrix: multiwall carbon nanotubes, graphite nano-platelets, expanded graphite platelets, and carbon black. Two-stage sorption and swelling behaviour was observed for all types of nanocomposites. An extent of the anomalous sorption depends on temperature, time and history of the test, and type of the filler. Diffusion-relaxation model of Berens and Hofenberg finely described sorption and resorption experimental curves, while desorption of all samples obeyed the Fick's law. The only additional parameter - relaxation time of polymer network - was introduced into general equations. The relaxation time increased with the addition of nanofillers and decreased with temperature increase. Dynamic mechanical thermal analysis was done to evaluate the plasticizing effect due to the absorbed water and to give an insight into the structural changes of the nanocomposites caused by their hydrothermal ageing. Water absorption resulted in plastification of the polymer that appeared in drop of glass transition temperature and lowering and broadening of tan δ peak, while after-cure and physical ageing effects appeared in the increased storage modulus.Publicationtype: Conference Paper1107 - Some of the metrics are blocked by yourconsent settings
Item type:Publication, Access status: without files , Hierarchical carbon fibre reinforced plastics with tailored nanoparticle modification - Benefits and limitations(Curran Associates, Inc., 2018-06); ; ; ; A tailored nanoparticle modification approach for fibre reinforced polymers (FRP) is presented that allows exact analysis of the impact of a nanoparticle matrix modification in either 0°- or 90°-layers of cross-ply laminates on the mechanical properties and damage mechanisms. A modification of the 0°-layers unexpectedly increases the quasi-static tensile strength, although dominated by fibre properties. Positive crack stopping effects as well as negative effects, such as accelerated delamination growth, are discussed. The applicability of nanoparticle modified resin systems to improve the performance of FRP-laminates is sensitive to the loading case. For laminates only loaded in tension a modification appears to be advantageous, whereas in case of bending or compression loads the effect of nanoparticles is ambiguous and should be applied carefully.Publicationtype: Conference Paper76